PLUMBING REPORTING
Plumbing Service Report Template: Free Example and Handover Checklist
A plumbing service report records what happened during a visit: the problem reported, the condition observed, the work completed, the checks performed and anything still open.
A useful report helps the customer understand the outcome and gives the office or next technician enough detail to follow up without reconstructing the job from messages and loose photos.
Use the free template below, then compare it with the completed example and run the handover checklist before sending your report.

Free plumbing service report template
Copy this worksheet into your document editor. Use the printable PDF for handwritten notes or the editable Word version to adapt the fields to your workflow.
Record only work and checks actually performed. Use “N/A” where appropriate and add a continuation sheet when a short field cannot explain the job clearly. Local requirements vary; this template does not replace required records.
PLUMBING SERVICE REPORT
JOB DETAILS
Report ID:
Work order:
Customer / site:
Property address:
Unit / room / work area:
Fixture / asset ID:
Make / model (if relevant):
Pipe material / size (if relevant):
Technician:
Visit date:
Arrival / departure:
Permit / license reference (if required):
REQUEST AND SCOPE
Customer-reported problem:
Agreed work:
Scope changes / authorized by:
Access restrictions / areas not inspected:
FINDINGS
Observed condition / exact location:
Readings, units and measurement location:
Checks not performed:
Shutoff / isolation status (if relevant):
Water damage / hazards observed:
WORK PERFORMED
Actions completed:
Parts / materials: description, quantity, unit:
Part reference / installed or supplied:
VERIFICATION
Check performed:
Location / conditions:
Observed result:
Limits of the check:
PHOTO RECORD
Before: reference / location / caption:
During: reference / location / caption:
After: reference / location / caption:
Open item: reference / location / caption:
OUTCOME
Agreed work: complete / partial / not completed:
Temporary work (or None):
Remaining / separately recommended work:
Follow-up action / responsible person:
Target date (or Not agreed):
HANDOVER
Advice / instructions provided:
Customer / representative:
Acknowledgment — select what was confirmed:
[ ] Visit confirmed
[ ] Report reviewed
[ ] Agreed work accepted
Acknowledgment date:
If not obtained: reason / handover route:
PREPARATION AND REVIEW
Prepared by / date:
Reviewed by / date:
For teams working across time zones, add the time zone alongside the visit times.
Completed example: an accessible sink drain repair
The fictional example below uses the same headings and fields as the blank template. It shows how a completed repair can sit alongside a separate condition that still needs attention.
PLUMBING SERVICE REPORT — COMPLETED EXAMPLE
JOB DETAILS
Report ID: EXAMPLE-PL-018
Work order: EXAMPLE-WO-218
Customer / site: Example Office Building
Property address: Example address
Unit / room / work area: Second-floor breakroom
Fixture / asset ID: Sink S-02
Make / model (if relevant): Not recorded; fixture model
was not needed to describe this drain connection repair.
Pipe material / size (if relevant): Not recorded;
confirm if needed for a later replacement.
Technician: Example Technician
Visit date: April 15, 2026 — illustrative date
Arrival / departure: 10:20 a.m. / 11:05 a.m., local time
Permit / license reference (if required):
Not provided in this example; confirm requirements
and enter any required reference before use.
REQUEST AND SCOPE
Customer-reported problem:
Water appears inside the cabinet after the sink is used.
Agreed work:
Inspect the reported leak and repair the accessible
drain connection if suitable.
Scope changes / authorized by:
None.
Access restrictions / areas not inspected:
Accessible under-sink drain connection examined.
Concealed pipework and cabinet structure not assessed.
FINDINGS
Observed condition / exact location:
Dripping observed at the accessible trap connection
beneath Sink S-02 while the sink drained.
Readings, units and measurement location:
No instrument readings taken. Findings were based
on visual observation during sink drainage.
Checks not performed:
Water pressure measurement, concealed pipework checks
and cabinet structure assessment were not performed.
Shutoff / isolation status (if relevant):
Supply shutoff valves were not operated or assessed
during this drain connection repair.
Water damage / hazards observed:
Staining observed on the cabinet base.
Its extent and cause beyond the observed leak
were not assessed.
WORK PERFORMED
Actions completed:
Replaced the trap connection seal and reassembled
the accessible trap connection.
Parts / materials: description, quantity, unit:
Trap connection seal — 1 each.
Part reference / installed or supplied:
Installed. Part reference not recorded;
office confirmation remains open.
VERIFICATION
Check performed:
Three sink fill-and-drain checks.
Location / conditions:
Sink S-02; accessible trap connection observed
while the sink drained.
Observed result:
No dripping observed at that connection
during the three checks.
Limits of the check:
Result applies to the observed connection during
these checks. Concealed pipework and cabinet
condition were not assessed.
PHOTO RECORD
Before: reference / location / caption:
B01 / beneath Sink S-02 /
Moisture at the accessible trap connection before repair.
During: reference / location / caption:
D01 / beneath Sink S-02 /
Trap connection and replacement seal during repair.
After: reference / location / caption:
A01 / beneath Sink S-02 /
Accessible connection following the final drain check.
Open item: reference / location / caption:
O01 / cabinet base beneath Sink S-02 /
Cabinet staining requiring separate review.
OUTCOME
Agreed work: complete / partial / not completed:
Complete — accessible drain connection repair.
Temporary work (or None):
None.
Remaining / separately recommended work:
Separate review of cabinet staining.
Confirmation of the installed seal's part reference.
Follow-up action / responsible person:
Site manager to arrange cabinet review.
Office to confirm the part reference before
the report is finalized.
Target date (or Not agreed):
Cabinet review: not agreed.
Part reference: before report finalization.
HANDOVER
Advice / instructions provided:
Report any recurring moisture.
Cabinet staining remains a separate open item.
Customer / representative:
Designated site manager.
Acknowledgment — select what was confirmed:
[ ] Visit confirmed
[ ] Report reviewed
[ ] Agreed work accepted
No acknowledgment obtained at the visit.
Acknowledgment date:
N/A.
If not obtained: reason / handover route:
Site contact unavailable at departure.
Report sent to the designated site manager;
acknowledgment pending.
PREPARATION AND REVIEW
Prepared by / date:
Example Technician / April 15, 2026.
Reviewed by / date:
Pending office review and part-reference confirmation.
The report distinguishes completion of the agreed repair from completion of every issue at the site. It also makes the missing part reference visible instead of silently treating the report as finalized.
Separate the reported problem from your findings
“Customer reports a leak” and “dripping observed at the trap connection” describe different things. Keep them separate so the reader can follow the evidence.
| Report element | Example |
|---|---|
| Customer report | Water appears inside the cabinet after sink use. |
| Technician observation | Dripping observed at the accessible trap connection while the sink drained. |
| Work performed | Trap connection seal replaced and connection reassembled. |
| Verification | No dripping observed during three fill-and-drain checks. |
| Remaining item | Cabinet staining requires separate review. |
Avoid replacing these details with “leak fixed.” That phrase leaves the location, work and basis for the result unclear.
Give each photo a clear purpose
A photo reference should connect the image to a location and a specific statement in the report.

| Photo | Purpose | Example caption |
|---|---|---|
| B01 — Before | Show the reported condition | Moisture at the accessible trap connection beneath Sink S-02 before repair. |
| D01 — During | Document the work | Trap connection and replacement seal during repair. |
| A01 — After | Show the completed work | Accessible connection following the final drain check. |
| O01 — Open item | Preserve a condition needing follow-up | Cabinet base staining beneath Sink S-02; separate review required. |
An after photo shows visible condition at a moment in time. Describe any checks separately rather than expecting the image to establish the result on its own.
For more examples, see the before-and-after photo report guide.
Describe checks precisely
A useful verification entry answers four questions:
- What did you check?
- Where and under what conditions?
- What did you observe or measure?
- What did the check leave unassessed?
If you record a measurement, include the value, unit and measurement location. If a relevant check was not performed, say so.
In the example, “no dripping observed during three fill-and-drain checks” is more specific than “all plumbing tested.” It tells the reader what supports the result without expanding the visit into a whole-system inspection.
Make temporary work and return visits visible
Use the outcome section to distinguish between situations such as:
- A temporary measure completed, with further work required.
- Investigation completed, with repair awaiting approval.
- Parts supplied, with installation still outstanding.
- The agreed repair completed, with a separate condition requiring review.
For each open item, record the next action, the responsible person and the target date. If a date has not been agreed, write “Not agreed.”
A clear job completion report can follow the same approach when several trades or visits contribute to one job.
Seven checks before handing over the report
Before sending the report, confirm that:
- The site, room and fixture can be identified.
- The customer request and agreed work are recorded separately.
- Parts and materials state what was installed or supplied.
- Verification describes the actual checks and their limits.
- Photo references match the correct images and locations.
- Open work has a next action and an owner.
- The recipient and meaning of any acknowledgment are clear.
If the customer signs, record what they are confirming: the visit, review of the report or acceptance of the agreed work. Do not sign on their behalf. If they are unavailable, record how the report was handed over and leave acknowledgment pending.
When a manual template becomes difficult to manage
A document template can support a straightforward visit. As reporting volume grows, check whether your team is spending time matching photos to jobs, rebuilding reports or chasing missing details after technicians leave the site.
When comparing a reporting workflow, try it with a representative plumbing visit:
- Can the reader identify the correct job and fixture?
- Do notes and photos remain connected?
- Are completed work and open items easy to distinguish?
- Can someone review the report before handover?
- Can the office find it when a customer calls later?
Use the field service report software guide to evaluate those needs against your team's workflow.
Frequently asked questions
What should a plumbing service report include?
Include job details, the reported problem, agreed scope, findings, work performed, materials, verification, photo references, open items and handover details. Add equipment identifiers, measurements and other fields when relevant to the visit.
Is a plumbing service report the same as an inspection report?
A service report documents a particular visit and its agreed work. An inspection report documents an inspection against a defined scope. A limited repair visit should not be presented as a complete plumbing inspection.
Should every report include water pressure?
Record pressure when it is relevant and was actually measured. Include the value, unit, location and conditions. Do not enter an estimated reading or imply that a pressure check occurred when it did not.
How should unfinished work be recorded?
State what remains, why it remains open, the next action, who is responsible and the agreed date. Distinguish temporary work from the intended final repair.
Can the report replace an invoice?
A service report explains the visit and its outcome. An invoice requests payment. They can refer to the same work order while serving different purposes.
Build a clearer handover
Use this template on a representative visit and check whether someone who was not there can understand the work, evidence and next steps.
See another completed field service report example, or explore Fieldnox for your field reporting workflow.